Palisade Fencing Cost UK 2026: How Much Per Metre?
Palisade fencing cost in the UK in 2026 typically runs from around £71 per metre for 1.8m galvanised palisade up to £132 per metre for heavy 3.0m runs, for the materials supplied. The exact price depends on the height, whether you choose W or D section pales, and the fixing type. This guide gives real per-metre supply prices, explains what drives the cost, and includes a calculator to work out your run.
How Much Does Palisade Fencing Cost?
For the materials supplied, galvanised steel palisade fencing costs roughly £71–£132 per metre depending on height and specification. Once you add installation — posts set in concrete or bolted down, plus labour — a fully installed palisade fence commonly lands around £110–£200+ per metre. The table below shows real supply prices from Rackerman by height, sold as 2.75m runs and individual components.
| Height | Supply cost (per metre) | Per 2.75m run |
|---|---|---|
| 1.8m | £71 – £88 | £196 – £241 |
| 2.0m | £77 – £95 | £211 – £260 |
| 2.1m | £82 – £100 | £225 – £274 |
| 2.4m | £91 – £110 | £249 – £302 |
| 3.0m | £110 – £132 | £302 – £363 |
The lower figure is in-concrete posts with W-section pales; the higher is bolt-down posts with heavier D-section pales. Prices are for the galvanised materials supplied.
Palisade Fencing Cost Calculator
Enter your run length, height and options for an indicative materials cost. Palisade is supplied in 2.75m runs, so the calculator rounds up to whole runs.
Palisade Fence Cost Estimator
What Affects Palisade Fencing Cost?
Height
Taller fences use more steel and bigger posts, so cost rises with height — from 1.8m for domestic and light commercial boundaries up to 2.4m and 3.0m for higher-security perimeters. Remember planning limits: a fence over 2m generally needs planning permission, as covered in our guide on fence height rules.
W Section vs D Section Pales
Pales come in two profiles. W-section (typically 2.0mm) is the standard, cost-effective choice for most boundaries. D-section (typically 3.0mm) is a heavier, stronger profile that resists attack and bending better, costing a little more — the right choice for higher-security sites. Both are usually triple-pointed at the top to deter climbing.
Fixing: In-Concrete vs Bolt-Down
Posts are either set in concrete (cheaper materials, but you dig and concrete each post) or supplied with a bolt-down baseplate (more expensive post, but bolts to an existing concrete surface — faster and ideal where you can't dig). Bolt-down is dearer per run but can save on groundwork.
Finish
Standard palisade is hot-dip galvanised for decades of outdoor life. A polyester powder-coated (PPC) colour finish over the galvanising adds cost but gives a coloured, duplex-protected finish. For how long the zinc lasts, see does galvanised steel rust.
Installation Cost
The figures above are for materials. Installation adds labour plus concrete and fixings — digging post holes, setting posts, and bolting up the rails and pales. As a rough guide, fitted palisade commonly totals £110–£200+ per metre depending on ground conditions, access and height. Bolt-down on existing concrete is quicker; in-concrete on difficult ground costs more. Gates, corners and raking to slopes are priced separately.
How Much Does Palisade Fencing Cost Across the UK?
Palisade prices vary a lot between suppliers, because "palisade fencing" covers a wide range of specifications. Sampling published supply-only prices from several UK palisade suppliers in July 2026 (galvanised, per metre, excluding VAT), typical figures look like this:
| Height | Typical UK supply price (£/m, ex-VAT) |
|---|---|
| 1.8m | £35 – £70 |
| 2.4m | £45 – £75 |
| 3.0m | £90 – £100 |
Sampled from several UK palisade suppliers, July 2026. Supply-only, galvanised, excluding VAT and delivery. 2.0m and 2.1m sit between 1.8m and 2.4m (roughly £39–£75/m). Prices move with the steel market and, above all, with specification.
Why do palisade quotes vary so much?
The gap between the cheapest and dearest quote for the "same" height almost always comes down to specification and what is actually included:
- Pale gauge and profile — a lighter 2.0mm W-section costs less than a heavier 3.0mm D-section, and some budget palisade uses thinner gauge again. Thinner steel is cheaper but easier to cut and bend.
- Post and rail sizes — a full BS 1722 Part 12 specification uses heavier posts and rails that step up with height. Lighter systems come in cheaper but are less robust.
- What's in the price — some headline "from" prices are bulk-quantity floors, or exclude posts, fittings or fish plates. Check the figure is for a complete run, not just the pales.
- Finish — galvanised is the baseline; a powder-coated colour finish adds cost.
- Supply vs installed — the figures above are supply-only. Fully fitted, palisade commonly runs £110–£200+ per metre once groundwork and labour are added.
When you compare quotes, compare like for like: the same height, the same pale profile and gauge, and a complete kit with posts and fittings to BS 1722 Part 12 — not just the lowest per-metre headline.
Is Palisade Fencing Worth It?
For security boundaries, palisade is one of the best value options: it is strong, hard to climb, hard to cut, and galvanised to last decades with no maintenance. It costs more than timber or basic wire fencing but far less than high-end welded mesh security systems, and it deters intruders far better than a domestic panel fence. For the full range of options, see our guide to types of metal security fencing.
Buy Palisade Fencing at Rackerman
Rackerman supplies galvanised steel palisade fencing as complete 2.75m runs or individual components — all heights (1.8m, 2.0m, 2.1m, 2.4m and 3.0m), W and D section, bolt-down or in-concrete, on one product page with a built-in calculator. Enter your fence length to build your order, or browse the full galvanised palisade fencing range.
Browse palisade fencing and build your run at Rackerman →
Frequently Asked Questions
How much does palisade fencing cost per metre?
Galvanised palisade fencing costs roughly £71–£132 per metre for the materials supplied, depending on height (1.8m to 3.0m), W or D section pales, and fixing type. Fully installed, it commonly totals around £110–£200+ per metre once labour, concrete and fixings are included.
How much is a 2.4m palisade fence?
2.4m galvanised palisade costs about £91–£110 per metre to supply, or roughly £249–£302 per 2.75m run, depending on whether you choose W or D section pales and in-concrete or bolt-down posts. Installation is extra.
Why do palisade fencing prices vary so much between suppliers?
Mostly specification. Pale gauge (2.0mm W vs 3.0mm D), post and rail sizes, and whether the price includes posts and fittings all move the figure — and a headline "from" price is often a bulk-only floor or pales-only. Compare like for like: same height, same profile and gauge, a complete kit to BS 1722 Part 12, and check whether it is supply-only or installed.
What is the difference between W and D palisade pales?
W-section pales (typically 2.0mm) are the standard, cost-effective profile. D-section pales (typically 3.0mm) are heavier and stronger, resisting bending and attack better, for a higher-security finish at a slightly higher cost. Both are usually triple-pointed.
Is palisade fencing cheaper than welded mesh?
Generally yes. Palisade gives strong security at a lower cost than high-specification welded mesh (358) security systems, while offering better deterrence than timber or basic wire fencing. The best choice depends on the security level and look you need.
Should palisade posts be set in concrete or bolted down?
In-concrete posts are cheaper to buy but need holes dug and concreted. Bolt-down posts cost more but fix straight to existing concrete, saving groundwork and time. Choose bolt-down where you can't dig, and in-concrete on open ground.
How long does palisade fencing last?
Hot-dip galvanised palisade lasts decades outdoors with no maintenance, because the zinc coating protects the steel sacrificially. Life is shorter in coastal or industrial air; a powder-coated duplex finish extends it further. Galvanised steel typically protects for 25–40 years or more.
Do I need planning permission for palisade fencing?
A fence over 2 metres generally needs planning permission, and 1 metre next to a highway. Since palisade is often 2.4m or 3.0m for security, planning permission is frequently required — check with your local authority before installing.
Does palisade fencing come in colours?
Yes. Standard palisade is galvanised grey, but a polyester powder-coated (PPC) colour finish can be applied over the galvanising for a coloured, duplex-protected look, at extra cost. Black and green are common choices.