Iroko Worktops: Pros, Cons, Care & Iroko vs Oak (UK Guide)
Share
Quick answer: an iroko worktop is a solid hardwood worktop in a warm golden-brown that darkens over time. It's naturally durable with a good resistance to moisture and decay, which makes it a popular choice round a kitchen sink. It's often called "African teak". Compared with oak, iroko is harder, copes better with moisture and has a richer colour. It still needs a proper oiled finish, as no timber is waterproof. Oak has bolder grain and is the more traditional British look. Both can be sanded and re-oiled for decades. This guide covers iroko's pros and cons, iroko vs oak, how to oil it and how its colour changes.

Which Worktop Wood Suits You?
Pick what matters most for your kitchen for an instant recommendation.
What Is Iroko?
Iroko is a tropical hardwood from West and Central Africa. Freshly cut it is a yellowish-brown, and with light and oil it mellows to a deep golden or copper brown. The grain is usually interlocked, which gives a subtle ribbon effect along the board. Its appearance and durability earn it the "African teak" nickname, although it isn't related to real teak. That durability is why iroko has long been used for boat building, outdoor furniture, draining boards and sink surrounds.

Iroko Worktop Pros and Cons
| Pros | Cons |
|---|---|
| Naturally durable with good moisture resistance, so a strong choice around sinks and Belfast sinks (still needs sealing) | Darkens noticeably over the first months. Expect the colour to change. |
| Heartwood is very durable and resists rot and decay | The natural oil means the first coat of finish needs preparing properly (see below) |
| Warm golden-brown tone that suits shaker, rustic and modern kitchens | Interlocked grain and occasional hard mineral deposits can tear out or blunt tools. Use sharp, carbide-tipped blades. |
| Can be sanded and re-oiled, so it refreshes instead of wearing out | Iroko dust can irritate skin and airways. Use dust extraction and an FFP3 mask when cutting or sanding. |
| Suits utility rooms, and outdoor kitchens with an exterior-grade finish | Usually costs more than beech and similar to or more than oak |
Iroko vs Oak Worktops
| Iroko | Oak | |
|---|---|---|
| Colour | Golden to copper brown, darkens with age | Honey-brown, ambers gently with oil |
| Grain | Interlocked, subtle ribbon figure | Open, bold grain with medullary-ray flecks |
| Water resistance | Very good: naturally durable | Good: tannins add natural durability |
| Hardness (Janka, approx.) | ~1,260 lbf | ~1,120 lbf (European oak) |
| Best for | Sink runs, Belfast sinks, utility rooms, outdoor kitchens | Classic British kitchens, islands, statement grain |
In short, choose iroko if water resistance and a rich, warm colour come first. Choose oak if you want the classic grain and a lighter tone. Want something darker still? Look at solid walnut. Comparing the lighter woods? Read oak vs beech worktops.
Is Iroko Good for a Kitchen Worktop?
Yes. It's one of the best timbers for a kitchen worktop, especially if the run includes a sink, dishwasher or Belfast sink. Its natural durability means it copes with splashes better than most hardwoods. Like any wood worktop, it still needs sealing on every face and edge, and spills shouldn't be left to stand.
How to Oil an Iroko Worktop
Iroko's natural oils can stop a finish soaking in, so the first coat needs a little preparation:
- Prepare. Make sure the worktop is clean, dry and lightly sanded. If your oil manufacturer recommends it, wipe the surface with white spirit and let it evaporate fully. This removes surface oils so the finish can key in.
- First coat. Apply a thin coat of hardwax worktop oil (thinned slightly if the manufacturer allows). Work along the grain and wipe off any excess.
- Build up. Apply 2–3 coats in total, with extra on the end grain and around sink cut-outs. Don't forget the underside.
- Maintain. Re-oil every 6–12 months, or whenever water stops beading.
Our full guide to oiling a wooden worktop includes an oil-quantity calculator.
Does Iroko Change Colour?
Yes. Iroko starts lighter and more yellow, then darkens to a deeper golden or copper brown with exposure to light and oil, mostly in the first few months. Pre-oiled iroko arrives closer to its finished tone. A board that has been under a cut-out or a chopping board may look lighter at first. This evens out over time. Left outdoors without a finish, iroko weathers to a silvery grey.

Cutting and Fitting Iroko
Iroko cuts well with a sharp, fine-tooth carbide blade, though mineral deposits can blunt tools faster. Use dust extraction and an FFP3 mask. Cut from the underside to reduce chipping and seal every fresh edge straight away. Need exact lengths? Use our worktop cutting service (£10 per straight cut), or message us your sizes for sink and hob cut-outs. Not sure which thickness you need? See our worktop thickness guide.
Buy Solid Wood Worktops at Rackerman
Our 38mm solid iroko worktop comes in 1m to 4m lengths, in 620mm and 950mm widths, sanded or pre-oiled, with free delivery to mainland England (surcharge for Wales, Cornwall, Devon and Scotland, shown at checkout). The full range:
- Solid oak worktop 38mm, 28mm and 20mm
- Solid beech worktop 38mm and 28mm
- Solid walnut worktop 38mm
- Solid iroko worktop 38mm
- Solid ash worktop 28mm
- Food-safe worktop oil and the worktop cutting service (£10 per straight cut)
Browse all solid wood worktops → · Ask about cut-outs or trade quotes →
Embed This Calculator on Your Website
Run a building, fabrication, landscaping or DIY website? You can add this free Worktop Wood Picker to your own page. Paste the code below into a Custom HTML block (WordPress), an HTML embed (Wix, Squarespace, Webflow) or straight into your page. It is free to use — all we ask is that you keep the credit link to Rackerman.
Frequently Asked Questions
What is an iroko worktop?
A solid hardwood worktop made from iroko, a West and Central African timber known as "African teak". It's golden-brown, naturally durable and has good moisture resistance.
Is iroko better than oak for a worktop?
For moisture resistance around sinks, generally yes, and iroko (~1,260 lbf) is also harder than European oak (~1,120 lbf). Oak has bolder grain and a lighter tone. Both are excellent if they're sealed and re-oiled.
What is the best oil for an iroko worktop?
A food-safe hardwax worktop oil. Follow the oil maker's preparation advice. Many recommend a white spirit wipe before the first coat so the oil can penetrate iroko's natural oils.
Does iroko go darker?
Yes. It darkens from yellowish-brown to a deeper golden or copper brown, mostly in the first few months.
Can iroko be used outside?
Yes, with an exterior-grade finish. Iroko heartwood is naturally durable and rot-resistant, which makes it popular for outdoor kitchens. Left unfinished, it weathers to a silvery grey.
Is iroko good around a Belfast sink?
Yes. Its natural durability makes it one of the best timbers for a Belfast or undermount sink run. Seal the cut-out edges and the underside thoroughly before fitting.
What thickness does an iroko worktop come in?
Our solid iroko worktops are 38mm thick (often listed as 40mm), the standard thickness for UK kitchen units.