Our EPDM rubber roofing membrane is a one-piece synthetic rubber roof covering for flat and low-pitched roofs: sheds, garages, extensions, dormers, garden rooms, porches and carports. Supplied as a single seamless sheet in 1.2mm or 1.5mm thickness, in sizes from 2m x 2m to 6m x 4m. One sheet covers the whole roof with no joints to fail. Choose your thickness and sheet size above. If you're not sure which size to order, the measuring guide below shows how to work it out.
EPDM sheet sizes
| Sheet size | Area | Largest roof deck it covers (150mm overhang each edge) |
|---|---|---|
| 2m x 2m | 4m² | 1.7m x 1.7m |
| 2.5m x 2m | 5m² | 2.2m x 1.7m |
| 3m x 2m | 6m² | 2.7m x 1.7m |
| 3m x 2.5m | 7.5m² | 2.7m x 2.2m |
| 3m x 3m | 9m² | 2.7m x 2.7m |
| 4m x 3m | 12m² | 3.7m x 2.7m |
| 5m x 3m | 15m² | 4.7m x 2.7m |
| 6m x 3m | 18m² | 5.7m x 2.7m |
| 4m x 4m | 16m² | 3.7m x 3.7m |
| 5m x 4m | 20m² | 4.7m x 3.7m |
| 6m x 4m | 24m² | 5.7m x 3.7m |
If your roof has an upstand against a wall, allow extra on that edge. Always measure your own roof using the method below.
How to measure for an EPDM roof
Measure the length and width of the roof deck itself, not the building footprint. Then add an allowance on every edge so the membrane can wrap over the fascia or drip edge and lap into the gutter. As a rule of thumb:
- Add at least 150mm to each edge, which means 300mm to both the length and the width.
- Where the roof meets a wall, add the full height of the upstand, usually 150mm or more, on that edge.
- Round up to the next sheet size. A little spare is easy to trim, but a sheet that's too short can't be fixed.
Example: a 2.4m x 1.8m shed roof needs at least 2.7m x 2.1m of membrane, so order the 3m x 2.5m sheet.
1.2mm or 1.5mm EPDM?
1.2mm EPDM is the standard thickness for most domestic flat roofs, including sheds, garages, porches and dormers. It is flexible, lighter to handle and the most economical choice. 1.5mm EPDM is the heavier-duty membrane for roofs that will see foot traffic for maintenance, larger extensions and garden rooms, and anywhere you want extra puncture resistance. If the roof will be walked on regularly or carry heavy plant, choose 1.5mm.
Why choose an EPDM rubber roof?
- One piece, no seams: a single sheet covers the whole roof, so there are no joints to leak.
- Long life: EPDM resists UV, ozone, frost and heat without cracking, splitting or blistering like felt.
- Cold applied: no torches or hot bitumen. It is bonded with adhesive, making it safe and DIY-friendly.
- Flexible: EPDM stays flexible in cold weather and handles the movement of timber roof decks.
- Low maintenance: keep it clear of debris and check the edges occasionally. EPDM can be patched easily if it is damaged.
EPDM vs roofing felt vs GRP fibreglass
Roofing felt is cheapest up front, but it cracks and blisters and typically needs replacing within about 10 years on a shed. GRP fibreglass is hard-wearing but needs dry weather, careful mixing and some skill to lay well. EPDM sits between the two: it is quick and forgiving for a DIYer to install, laid cold in one piece, and lasts far longer than felt. For most sheds, garages and garden rooms it is the best value flat roof covering.
How to fit an EPDM rubber roof
- Prepare the deck: the roof must be a sound, dry, smooth timber deck. 11mm or 18mm OSB3 board is the usual choice. Remove old felt, nails and debris.
- Relax the membrane: unfold the sheet on the roof and leave it for around 30 minutes to relax and flatten.
- Bond the field: fold back half the sheet, roll water-based deck adhesive onto the board, lay the membrane back and brush out air. Repeat for the other half.
- Bond the edges: use contact adhesive on the perimeter, upstands and any vertical faces.
- Finish the edges: fit edge trims or drip trims and gutter trims, then trim the surplus membrane.
Always follow the adhesive manufacturer's instructions for coverage, temperature and curing times. Don't apply adhesive in wet weather or below about 5°C.
What else you need
A complete EPDM roof needs water-based deck adhesive for the main area, contact adhesive for the perimeter and upstands, and edge, drip and gutter trims. Building or re-decking the roof as well? See our OSB3 boards for the deck and sawn treated timber for rafters and firrings. For insulated garden room roofs, browse insulation boards and roofing sheets.